Currently Supported Sims:

• Falcon 4 (AF, BMS, OF, FF)
• X-Plane V9
• IL2
• IL2-FB
• Pacific Fighters

Features:

• Auto launch user defined sim and configuration file at windows startup.
• Auto loads user assigned configuration files when sim detected.
• Assign different configuration file for each sim.
• Supports unlimited number of devices.

INPUTS

• Assign up to 8 separate "On Press" & "On Release" key macros to each button.
• Definable Key hold delay.
• Definable Key Macro delay.
• Key Repeat and Hold options.
• Unlimited button assignments.
• Unlimited input devices.

OUTPUTS

• Supports all USB module output modes.
• Supports conditional logic for controlling magnetic switches and other outputs.
• Supports user defined light bits. Can be assigned to outputs to control LED's, lamps, magnetic switches, etc.
• Supports 7-segment displays.
• Supports CRT RWR mode. Can be used to display RWR on any suitable CRT such as an oscilloscope.
• Supports graphical LCDs for DED and PFD.
• Supports DACs for Air-Core meters and servos for various instruments and gauges. Up to 8 individually configurable sections can be defined for multi-scale gauges.
• Dot Matrix Displays for CDMS panel.

The following sims will be added if there is sufficient demand.

• MS FSX
• Blackshark
• LOMAC
• All Simbin racing titles (GTR, RACE, etc.)
• rFactor
• Arca simracing
• LFS
• NR2K3
• RBR
• iRacing

New Features that will be added for the sims listed above:

• Fully user configurable LCD display with support for multiple pages of data. Useful for displaying Comms info in FSX and telemetry data in racing sims.
• Cycle pages using button inputs.
  Multiple data pages for 7-Segment displays. Cycle pages using button inputs.
• Selectable Metric or Imperial Units option.
• Additional telemetry data support such as tire info (i.e. wear, temp, etc.) if available from the sim.
• Ability to support multiple USB modules at the same time. No longer limited to 1 device as in RSIM.

Requires one free USB port.

• 8 I/O Ports per card (120 I/Os)
• PnP Expansion port
• Ports individually configurable in multiple modes:
  • Direct Mode
  • Multiplexed Mode
  • Vector Graphics Mode
  • SPI Mode (8-32 bits data word)
  • GLCD Mode (192 x 64, 256 x 64)
  • Latched Output Mode
  • Dot Matrix Mode (4 5 x 7)
• Can sink/drive up to 3 Amps per card
• Dual voltage support (5V Adj.)
• Short circuit protection
• Serial ID: Connect multiple modules without conflict
• Firmware updates via USB
• Requires standard PC power supply
• Full-Speed USB HID compliant device
• Employs Windows default drivers
• 1 year limited warranty on parts and labor

2 Port version of the ElectronFlux

15 ch Power & Relay Output Card

• 10 x 30V Outputs
• 5 Relay Outputs
  • Resistive Loads
    • 7A 250 VAC
    • 12A 125 VAC
    • 10A 28 VDC
  • Inductive Loads
    • 3A 125 VAC

• 35 mA/ch
• Onboard PWM brightness control

• Onboard PWM brightness control suitable for both LED & EL based backlights.

• 10-bits/ch (1024 steps)
• 5V output supplied by EFlux or external PSU

Specs TBD.

Preliminary Features:

• 56 N-Channel outputs. Switches ON to common GND.
• 5A max per channel. (10A peak for short durations)
• 300W max power dissipation per output
• 100V max per channel
• Built-in body diodes suitable for low inductive kickback
• Individual channel voltages
• Screwless terminal blocks
• Onboard PWM brightness control
• Individual channel PWM brightness control
• 8 Relay outputs (NO & NC outputs).
  • Resistive Load
    • 7A 250 VAC
    • 12A 125 VAC
    • 10A 28 VDC
  • Inductive Load
    • 3A 125 VAC

• Air-Core based
• 10-bits (1024 steps)
• Dual EL backlight white / green

• Air-Core based
• 10-bits (1024 steps)
• Dual EL backlight white / green

• Air-Core based
• 10-bits (1024 steps)
• Dual EL backlight white / green

SPI based panel mount 2" magnetic compass with white and green internal lighting. Metal housing with coated glass.

• Air-Core based
• 10-bits (1024 steps)
• Dual white / green lighting

• Air-Core based
• 10-bits (1024 steps)
• 0.28" LED character height (green)
• Dual EL backlight white / green

Unlike the CRT vector mode on the EFlux which uses dots to draw lines, this version employs a high speed FPGA for onboard graphics generation and produces sharp continuous traces.

• High speed vector based hardware implementation for smooth graphics
• Built in symbols based on F-16 RWR
• Supports 100+ simultaneous onscreen symbols
• 60Hz refresh rate
• Supports user generated custom symbols
• Firmware updates through ElectronFlux
• Metal housing with etched coated glass. Conforms to MS33556.
• Operates on 12V supplied by any suitable PC PSU
• 1 Year warranty on parts and labor except CRT tube. Spare CRT tube included.

• USB standalone version
• USB bus powered
• Firmware updates via USB

• Yellow OLED based graphic LCD in black painted aluminum box.
• 256 x 64 pixels.
• Real military fonts.
• 1" x 3" black painted aluminum box.

32 point breakout board for LO-LED64

• 480 Digital Inputs
• supports 1 16x16 scan matrix
• Improved high speed rotary encoder support from V2
• Up to 16 rotary encoder support. Individually assignable rotary inputs. No more wasted inputs as was the case with V2.
• 32 individually configurable inputs supporting various modes:
  • Rotary Encoder (1X, 2X, 4X decoding)
  • Pulsed
  • Toggle
  • Momentary
• No diodes required
• Short circuit protection
• Serial ID. Connect multiple modules without conflict.
• Software configurable
• Software keyboard emulation
• Firmware updates via USB
• USB bus powered
• Full-Speed USB HID compliant device
• Windows default drivers

• 64 digital inputs expandable to 128, supporting several modes:
  • Rotary Encoder (1X, 2X, 4X decoding)
  • Pulsed
  • Toggle
  • Momentary
• No diodes required
• Up to 32 rotary encoders supported (3 types)
• Push-Pull rotary switch support
• Expansion Port: Supports 6x8 Scan Matrix (48 inputs) or GT-64X expansion card (64 inputs).
• Short circuit protection
• Serial ID. Connect multiple modules without conflict.
• Software configurable
• Software keyboard emulation
• Firmware updates via USB
• USB bus powered
• Full-Speed USB HID compliant device
• Windows default drivers

• 8 Analog 12-Bit (4095 steps) Axis Inputs
• Hardware calibration support. No calibration in Windows required.
• Axis trim and dead zone settings
• Configurable inputs: 16 direct (no diodes required) or 64 scan matrix (8x8) inputs supporting several modes:
  • toggle
  • pulsed
  • momentary
  • rotary
  • mode
• Supports a 3 mode selection switch for HOTAS setups. Mode selection Controls inputs 1 through 6
  • Mode 1: inputs 1-6
  • Mode 2: inputs 17-22
  • Mode 3: inputs 33-38
• Up to 8 rotary encoders supported (3 types)
• 2 POV HAT (8-way)
• Mouse cursor support. Control mouse using POV HAT inputs
• 2 Mouse buttons
• User adjustable digital filtering algorithm support
• Serial ID. Connect multiple modules without conflict.
• Firmware updates via USB
• USB bus powered
• Full Speed USB HID compliant device

• 1 Digital 16-Bit Industrial Incremental Encoder support
• 6 Digital 13-Bit Industrial Absolute Encoder support
• 8 Analog 12-Bit (4095 steps) Axis Inputs
• Hardware calibration support. No calibration in Windows required.
• Axis trim and dead zone settings
• Up to 24 Button Inputs (88 with GT-64X expansion card) supporting several modes: toggle, pulsed, momentary, rotary
• No diodes required on any inputs
• 2 POV HAT (8-way)
• Up to 8 rotary encoders supported (3 types)
• 20x4 Character LCD (HD44780 interface)
• 7-Segment display support for Gear Indicator in racing sims
• LED Bar Graph support for RPM indicator in racing sims
• User adjustable digital filtering algorithm support
• Expansion port
• Serial ID. Connect multiple modules without conflict.
• Firmware updates via USB
• USB bus powered
• Full Speed USB HID compliant device

USB Module. Composite device. Enumerates as 2 Joysticks with 32 Digital, 8 Analog Inputs & 2 POV HATs each.

• 16 Analog 12-Bit (4095 steps) Axis Inputs
• Hardware calibration support. No calibration in Windows required.
• Axis trim and dead zone settings
• 4 Servo support for use with auto throttles or motion systems. 10-bits / ch (1024 steps)
• Configurable inputs: 64 direct inputs (no diodes required) supporting several modes:
  • toggle
  • pulsed
  • momentary
  • rotary
• Up to 16 rotary encoders supported (3 types)
• 4 POV HAT (8-way)
• Mouse cursor support. Control mouse using POV HAT inputs
• 2 Mouse buttons
• User adjustable digital filtering algorithm support
• Serial ID. Connect multiple modules without conflict.
• Firmware updates via USB
• USB bus powered (Servos require an AC Adapter)
• Full Speed USB HID compliant device

• 10 user selectable Frequency and PWM outputs capable of controlling real Aftermarket automotive gauges
• 16 12V outputs for controlling real automotive indicators and shift light
• 10 Digital 10-bit SPI outputs for controlling any SPI based simulated gauges
• 7-Segment display support for Gear position indicator
• LED Bar graph RPM display
• 20x4 Character LCD (HD44780 interface)
• User adjustable fluid damping algorithm for smooth gauge pointer movement
• Serial ID. Connect multiple modules without conflict
• Firmware updates via USB
• Short circuit protection
• Full Speed USB HID compliant device
• Powered by any suitable PC PSU

• 8 Digital 10-bit SPI outputs compatible with standard Air-Core driver ICs
• 7-Segment display support for Gear position indicator
• Shift light output
• LED Bar graph RPM display
• 20x4 Character LCD (HD44780 interface)
• User adjustable fluid damping algorithm for smooth gauge pointer movement
• Serial ID. Connect multiple modules without conflict
• Firmware updates via USB
• Short circuit protection
• Self powered using standard AC adapter
• Full Speed USB HID compliant device

Includes cable and black acrylic housing.
Specify KPH/MPH and color when ordering. Yellow and Red versions available only in KPH.
Compatible with NITRO-XG & SLG

Compatible with NITRO-XG & SLG

F1 wheel display based on BMW design.

• 2 Analog 12-Bit (4095 steps)
  Axis Inputs for clutch and brightness control
• Configurable inputs: 32 direct inputs (no diodes required)
  supporting several modes:
  • toggle
  • pulsed
  • momentary
  • rotary
• Up to 16 rotary encoders supported (3 types)
• 2 POV HAT (8-way)
• 16 individually controlled LEDs
• 9 7-segments displays.
• 20 x 2 LCD
• All aspects of the displays are fully customizable through USIM.
• Mouse cursor support. Control mouse using POV HAT inputs
• 2 Mouse buttons
• Serial ID. Connect multiple modules without conflict.
• Firmware updates via USB
• USB bus powered
• Full Speed USB HID compliant device
  
  USB Standalone module.
  USB Cable included which fits through G25 shaft.
  Requires USIM. Not compatible with RSIM.